Sporlastic VERTEBRADYN STABIL Back Brace

$303.00

The VERTEBRADYN® STABIL is a lumbar brace for stabilising the lower back, one step firmer than VERTEBRADYN LIGHT. It is worn for lumbar pain and lumbar syndrome, for instability, for disc damage and after lumbar surgery.

The support comes from a stabilising element built into the back panel — anatomically pre-moulded steel bars that a fitter can bend to the wearer’s own shape. The brace is put on by putting a hand into the loop at each end, pulling it open behind the back and bringing it round; the closure plates are then tensioned over the abdomen and pressed together. Worn snugly it works as a pair: the bars steady the spine at the back while the abdominal pressure at the front takes load off it.

A QR code on the brace opens Sporlastic’s exercises and patient information.

Is this the right one for you?

Choose this if the pain is muscular or postural — everyday lower back pain, strain or fatigue, with no disc or joint diagnosis.

For disc problems: Sporlastic VERTEBRADYN AKTIV Back Brace is built for disc protrusion and prolapse.

For facet joint pain: Bauerfeind LumboLoc Back Brace relieves those small spinal joints specifically.

For pain lower down, across the pelvis or hips: Sporlastic VERTEBRADYN ISG Back Brace targets the joints where your spine meets your pelvis.

ColourPlatinum

Size XS S M L XL XXL

Chat with us for sizing help before you order
Free insurance estimate — right from your cart
Free shipping across Canada on orders over $125
Size exchange on unopened items

Order for pickup at 7225 Woodbine Ave

Usually ready in 2-4 days

Relief, reduction in lordosis (the natural inward curve of the lower back) and stabilisation of the lumbar spine
Improvement of posture

Polyamide 67%
Lycra 33%
Integrated anatomically pre-moulded steel bars

Conservative/post-operative
Lumbago
Lumbar pain
Osteochondrosis
Spondylosis
Spondylolisthesis
Intervertebral disc damage
Minor instability of the lumbar spine
Preventive stabilisation

Not suitable for: allergic, inflamed or injury-related skin changes over the area it covers (for example swelling or redness); impaired circulation or lymphatic soft-tissue swelling; nerve-related disturbance of sensation or of skin nourishment (trophism) in that area, with or without damage to the skin.

This is a medical-grade orthopaedic brace that incorporates rigid structural support. Braces and orthoses built with rigid components are commonly covered under Canadian extended health benefit plans (e.g. Sun Life, Manulife, Canada Life, Blue Cross, Green Shield Canada) when accompanied by a valid prescription from your physician or nurse practitioner. It may also qualify as an eligible medical expense under the CRA's Medical Expense Tax Credit. We're happy to prepare an itemized estimate for your insurer — use Get an Insurance Estimate for this item, or add several to your cart and request one for everything at once. No charge, and it's not an order. Coverage details, annual limits, and prescription requirements vary by plan, so please confirm your specific benefits with your provider and keep your prescription and itemized receipt for your claim.

Check the size chart below. If your measurements don't fit a size on it, contact us and we'll help.

sporlastic-vertebradyn-stabil-back-brace-sizing-guide.jpg

Size		XS	S	M	L	XL	XXL
Body circumference (cm)at the level of the navel	11	70 – 80	80 – 90	90 – 100	100 – 110	110 – 120	120 – 130

Wash the brace in lukewarm water (30 °C) with mild detergent and air dry
Do not dry it in the tumble dryer, on the heater or in the microwave
To avoid damaging other items of clothing during washing, it is best to wash the brace separately or close the hook-and-loop fasteners beforehand
If the tension of the knitted fabric decreases over time, it can be restored by washing
Sporlastic therefore recommends washing the brace more frequently

Sporlastic prints these steps in the instructions for use supplied with the product.

We recommend wearing a thin, tight-fitting T-shirt under the product.
The correct positioning of the VERTEBRADYN® STABIL is achieved when the stabilising element in the back section comes to rest centrally over the lumbar spine.
The front lower end of the brace should be flush and parallel to the thigh when seated and should not cause any pressure in the groin.
To put on the brace, insert your fingers into the loops on both sides of the VERTEBRADYN STABIL closure. Pull the brace apart behind your back with tension and guide it around your body.
Tighten the closure plates under tension over your abdomen. Pull your fingers out of the loops and close the hook-and-loop fastener of the VERTEBRADYN STABIL completely.
Make sure the closure plates lie flush on top of each other when you fasten them.
VERTEBRADYN STABIL should fit snugly with high compression. In this way, the combination of the stabilising element in the lumbar region and the abdominal support can provide significant relief for the spinal column. When you put it on with high compression, make sure it is still comfortable to wear.